Remove lose dust/grit with a vacuum cleaner, floor mop or other dry cleaning method.
Pretreatment before coating:
Depending on the level of contamination the Recoat Floor Cleaner can be diluted from 1:5 (standard) for normal cleaning, to 1:2 (1 litre cleaner to 2 litres of water) for deep cleaning.
Apply the diluted Recoat Floor Cleaner on a section of the floor by spray or mop.
Leave the solution on the substrate for 3-5 minutes to solve the embedded contamination. Scrub the treated section with a polishing machine or auto scrubber equipped with a white or red pad and remove all the dissolved contamination. When the entire floor is cleaned like this make one more overall run with the auto scrubber holding only clean water in the tank making sure to remove all cleaning residues.
Note: keep the quantity of water used for cleaning to a minimum. Be aware of large openings/crevices in the floor. Do not allow excessive amounts of cleaning solution in to run in the openings/crevices .
Note: when using the Recoat Floor Cleaner in high concentrations allow 2-3 hours drying time before using the floor.
For regular floor cleaning:
Dilute Floor Cleaner 1:50 to 1:100
Assessment of the surface is very important. The surface must clean, dry and free of grease, oil and other contaminants.
– First clean prefab concrete with the Recoat Etching Cleaner (see-TDS). For untreated and highly absorbent substrates depending on the suction, dilute the primer strongly (20-50%) with water.
– First clean ceramic surfaces with a sanding cloth in combination with the Recoat Bonding Cleaner (see TDS).
– First clean plastic surfaces with a sanding cloth in combination with the Recoat Cleaner.
– Metal (closed) surfaces first clean a sanding cloth in combination with the Recoat Bonding Cleaner (see TDS).
– Other surfaces first clean a sanding cloth in combination with the Recoat Cleaner.
Recoat Multi Primer reduces consumption and ensures optimum performance of the end product. Apply product as a “normal” waterborne paint; applying, distributing and holding off. Avoid working in the sun because of too fast drying.
Never apply Recoat products undiluted.
Advice to always make a test surface.
Assessment of the substrate is very important. The surface must be clean, dry and load-bearing, free, skin grease, oil etc.
Clean the surface with Recoat Floor cleaner
Then pre-treat the surface with the Recoat Multi Primer and after 2-12 hours apply Recoat Floor One XS. (see TDS sheets concerning products)
Always make sure you work wet in wet. Apply product as a “normal” water-borne lacquer; apply, distribute and stay off. Avoid working in the sun because of too fast drying. Try not to apply thick layers. Never apply recoat products undiluted.
Advice to always make a test surface.
Recoat Floor One XS is a high-quality clear coating system specially developed for environments where a durable, abrasion-resistant and safe flooring solution is required. Thanks to its low solvent content, this coating is universally applicable with no odour nuisance, making it ideal for both indoor and outdoor use.
Recoat Floor One XS is the ideal solution for those looking for a reliable, environmentally friendly and user-friendly coating with excellent performance and a safe finish.
| Location | Inside, Outside |
|---|---|
| Surface | Concrete, Linoleum, Mineral floors, Plastic, Terrazzo, Tiles |
| Special features | Against human excrement, Anti-Slip, Busy traffic area + 10,000 movements per day, Chemical resistant, Preventing urine stains /odor nuisance |
| Finishing | Silk |
SDS - EN - Recoat - Floor Cleaner
TDS - EN - Recoat - Floor Cleaner SDS - EN - Recoat - Multi Primer
TDS - EN - Recoat - Multi Primer
Tests Multi Primer
Recoat Product Comparison SDS - EN - Recoat - Floor One XS (R11)
TDS - EN - Recoat - Floor One XS (R11)
Schaafdries 12
5371 NJ Ravenstein
Nederland
